FC200 ECU programmer is designed for ECU/EGS clone, and it supports 4200 kinds of ECUS/EGS, 3 types of operation modes, involving 80% of the models on the market. FC200 unit has data loss prevention, automatic verification, 100% accurate analysis of BMW's ISN code, support for VIN code modification and data cloning of various models.
What's more, it has 3 exclusive support for DTC shielding and function shutdown. With the exquisite design, FC200 is your trusted auto repair assistant in various operating environments.
1. Original Parts Protection
FC200 supports OBD and platform mode for more than 98% of ECU/EGS. There is no need to open shell and no punch. FC200 protects original parts of the vehicle.
2. Smart Identification
The "identification" function can help users diagnose whether the ECU module is communicating and check whether the wiring is wrong.
If the ECU module is not damaged and can be communicated, and if the wiring is correct and identification is successful, FC200 can read chip and firmware information.
3. Module Clone
FC200 supports ECU/EGS reading&writing and modules clone, synchronization matching, without online programming, flash data by area, automatic check, chips and modules protection.
4. ISN Reading and Writing
FC200 supports all BMW series (including Mini) ECU ISN code acquisition , convenient for all keys lost matching and anti-theft fault maintenance.
5. VIN Writing
FC200 solves the problem of double VIN or VIN mismatch of vehicles, which is convenient for vehicle maintenance.
6. Data Processing
FC200 supports data analysis and modification for the 4th and 5th generations of Audi/Seat/Skoda/Volkswagen ECUs.
Turn off anti-theft system for Bosch MED/EDC17 series ECU
TPROT off function of Bosch VAG MEDC17 series, BMW/Mini MEVD17/EDC17 series, Hyundai/Kia EDC17/MED(G)17 series.
7. DTC Shielding
The engine DTC code can be shielded, such as the shielding of the 28A0/101F01 fault code of the BMW N55 engine, read the engine data via FC200, then load the data into the hexadecimal data modification tool, modify and save the bytes of the fault code comparison, and then use FC200 to load the modified data and write it back to ECU.
1. Auto ECU Programmer for repair necessary--Support BMW ECU Data reading, writing and clone.
Effectively solve the problem of replacing the second-hand computer after the damage of BMW ECU control unit, just need to read the original computer data and then clone it.
Support almost all the BMW ECU model for reading and writing: MSV90/ MSD85 MSD87 N20 N55 B48 B58 etc.
Successfully make up the market for BMW ECU reading and writing equipment, save you high equipment costs.
2. Auto Locksmith necessary-Support BMW IMMO functions, Read BMW ISN Code by OBD.
Quickly solve the problem for data collection of bmw all key lost.
With more stable and efficient irremovable functions.
If you want to do all key lost for BMW 3 Series 5 Series 7 Series X5 X6 GT535 Six-cylinder engine, must need ISN code to program the keys.
3. Work together with CGDI BMW, VVDI2 Full, Mini ACDP, AUTEL IM508, IM608 Pro, etc to program keys, save your money
(The cost of similar equipment is very expensive).
4. With stable and effective functions by professional quality test. It is easy to operate and quick to start.
5. Add Mercedes-Benz 271 Audi Volkswagen 06J and other ecu types (Some are paid service).
6. Full Version with All License Activated. Free Update Online for One Year. Annual fee needs to be checked with us after the first year. If you don't pay the annual fee, you can still use it, but some bosch ecu does not have the verification function (the function that needs to be connected to the server cannot be used)
7. Multi-Language: English, French, Spanish, Polish, Traditional Chinese and Simplified Chinese
8. With new update, FC200 not only support BMW ECU but also support over three thousands of ECUs like KTAG, Kess, kessy, Dimsport etc.
9. Bosch ECU serach : Free to find out what ECU type (except bosch made in China)
10. With CAN-bus ,and no disassembly (platform mode), and boot mode
FC200 Update Information:
FC200 V220.127.116.11 update information
1. Added search function by car brand in the main interface
2. Added BOSCH engine computer boot mode
ME17.0.3 ME17.1.1 ME17.1.6 ME17.2.4 ME17.3.0 ME17.7
ME17.8.31 ME17.9.20 ME17.9.21 ME18.104.22.168 ME17.9.74
ME17.9.51 ME17.9.52 MED17.1.10 MED17.8.10 MED17.9.3
MEV17.4 MEV17.2.1 MEDG17.0 EDC17CP05 EDC17CP09
3. Added BOSCH engine computer platform model MG1CS016
4. Added BOSCH Engine computer (BETA)
MD1CP001 MD1CP002 MD1CP006
MD1CP014 MD1CS001 MD1CS003
MG1CS008 MG1CS011 MG1CS018
5. Added and modified VIN model ME17.1.6
FC200 V22.214.171.124 (2021.12.23) NEW
1.New online store button: query the validity period of the equipment service
2.Added FC200 support list
3.Added Bosch engine platform modes: MEG17.0, MEG17.9.2, MEG17.9.8, MEG17.9.12, MEG17.9.13, MEG17.9.21
4.Added Bosch engine boot mode: MEG17.9.8, MEG17.9.12, MEG17.9.13
5.Added Bosch engine (test version): MD1CP004, MG1CS001, MG1CS002, MD1CS004, MD1CS005, MD1CS006
6.Optimize data processing-close the anti-theft system function (add a second closing method)
7.Optimize the engine menu and wiring diagram
8.Increase the zoom in and zoom out buttons in the wiring diagram interface
9.Optimize the clone function of Volkswagen DL382 gearbox
10.Fix some bugs and optimize software performance
Note: The equipment produced before 2021.09.10 will be automatically activated, and the service time will be valid until 2022.09.10. For equipment produced after this time, after the software is updated, a pop-up window will prompt to activate. Only after activation, some functions related to the server can be used normally. The validity period starts from the day of activation, and the validity period is one year.
FC200 V126.96.36.199 (2021.11.15)
1. Optimize the wiring diagram of BOOT mode of Bosch engine
2. Relaunch Bosch ME17.9.11 engine
3. Upgrade log for handling Spanish errors
4. Fix some bugs and optimize software performance
FC200 V188.8.131.52 (2021.11.02)
1. New ECU (Audi /Seat /Volkswagen /Skoda /Benz /Aston Martin /Aston /Maserati /Hyundai /Kia /Piaggio /Suzuki /Dacia /Renault /Smart /Ford /Opel / Saab /Vauxhall /Citroen /Jaguar /Land Rover /Peugeot) Read and write VIN: MED17.1.21, MED17.1.27, MED17.1.10, EDC17C66, MED17.7.7, MED17.7.5, MED17.3.4, EDC17C08, EDC17C57, ME17 .9.61, ME17.9.20, MED17.0.1, EDC17C19, EDC17CP42, MED17.4.2, MED17.9.9, MEDC17.9
2. New Bosch engine platform mode: MG1CS042
3. Optimize the password reading method of the boot mode of the doctor series engine
4. Optimize the operation interface of PFLASH calibration function
5. Fix some bugs and optimize software performance
FC200 V184.108.40.206 (2021.09.11):
1. Added SH725XX gearbox computer clone: read and write MAPS, read and write EEPROM, backup data, and restore data.
(1) Support all ZF_8HP gearbox computer clones: Alfa Romeo /Alpina /Aston Martin /Audi /Bentley /BMW /Chrysler /Dodge /
Great Wall /Iveco /Jaguar /Jeep /Lamborghini /Land Rover /Mann /Maserati /Porsche /Rolls-Royce /VinFast /Volkswagen
(2) Support VW/Audi/Skoda/Seat DQ380/DQ381 gearbox computer clone
(3) Support Benz/Nissan 9GTronic (VGS-NAG3) gearbox computer clone
(4) Support MINI/Renault/BMW 7-speed dual-clutch (Getarg 7DCT) gearbox computer clone
2. Added BMW gearbox clone model:
DKG(TC1766): Read and write DFLASH, EXT DFLASH, PFLASH
3. Added ECU (Chevrolet, Opel, Vauxhall) to read and write VIN: EDC17C59
4. New sub-function of BMW 6HP: Erase reset function
5. Added Bosch engine boot mode: MEVD17.2.7
6. Added Delphi engine boot mode: CRD2.x TC1797, CRD3.x TC1797
7. Optimize the engine computer read and write speed
8. Fix some bugs and optimize software performance
FC200 Software Features :
1. Interactive Interface
The level is clear, the function is clear, and the "brand-model-ECU" structure is used to help users save time and accurately find the operating directory.
2.Built-in Model Search
Support ECU model and Bosch number search, avoid the trouble of level selection, and enter the function interface as quickly as possible.
ECU Search: Take the BMW MSV90 engine computer as an example. First select "BMW", select "ECU" as the search condition, enter "MSV90", click the search button, and the ECU type will appear.
Bosch Number Search: Take the Volkswagen engine computer as an example. First select "Volkswagen", select "Bosch Number" as the search condition, and enter "0261S10525".
Please note that the Bosch number is a ten-digit number and the letters are capitalized. Click the search button, and the ECU type will appear.
3. Intuitive Wiring Diagram
Highly paid professional designers are hired to produce, 1:1 simulation, bright colors, to avoid user wiring errors.
FC200 Hardware Features:
FC200 Main Unit
1. Integrated injection of polymer materials, professional customized internal circuit boards, national patent certification
2. Exquisite design, easy to carry, can shield surrounding interference signals, adapt to various operating environments
3. There are 3 expansion ports for peripherals, which are automatically diagnosed and identified. They are 12V power port, USB port and DB15 port.The DB15 port can be connected to a free-dismantling adapter and OBD cable.
1.Vehicle-grade wiring harness, made of synthetic metal, has excellent internal conductivity, and can be used continously for 10,0000 times.
2. Tight design, seemless connection between ECU and host to ensure continuours communication and excort your operation
3. Equipped with B-type, C-type, D-type, F-type and G-Type pin interfaces, suitable for many types of ECU and EGS
FC200 obd2 cable mainly suitable for BMW B48/B58 ECU at present, read ISN via OBD without disassembly.
110cm, made of synthetic material, resistant to high temperature water-proof, anti-corrosion is designed according to OBD port of the vehicles, built-in anti-falling buckle make connection stable
FC200 ECU Programmer Wiring Diagram:
For Volkswagen ME17.5.22-TC1724:
For BMW N20 MEVD17.2.9-TC1797:
Supported Vehicle Models
Support 4200 kinds of ECUs, involving 80% of the models on the market.
European Cars: Abbas, Alfa Romeo, Aebi, Artec, Aston, Aston Martin, Audi, Bentley, BMW, Bugatti, Citroen, Dacia, CASE, CASE Tractors, Dallara, Deutz, DS, Ducati, Fendt, Ferrari, Fiat, Jaguar, KTM, Lada, Lamborghini, Lancia, Land Rover, MAN, Maserati, McLaren, Mercedes-Benz, MG, Mini, Opel, Peugeot, Piaggio, Porsche, Renault, Royal Enfield, Saab, SEAT, Skoda, Smart, Steyr, UAZ, Vauxhall, Volkswagen (VW), Volvo, Volvo Penta.
American Cars: Can-Am, Caterpillar, Chevrolet, Chrysler, Dodge, Ford, Ford Trucks, Freightliner, GMC, Indian, Internation, Jeep, Lincoln, New Holland, Polaris, Hidu.
Asian Cars: Force, Genesis Motors, Honda, Hyundai, Infiniti, Isuzu, Kassan, Kia, Kubota, Mahindra, Mitsubishi Fuso, Nissan, Subaru, Suzuki, Toyota.
Chinese Cars: Changan, Chery, Foday, Geely, Great Wall, Iveco, Jianghuai, Jiangling, Lifan, Ferguson, Valtra
1pc x CGDI FC200 ECU Programmer
About Shipping Way
1.DHL Shipping: 5-7 working days. With DHL shipping, we will declare lowervalue on invoice for customers to help customs clearrance .If customer have special requirements on declaring, please contact salesman on order page, online chat,email, skype or whatsapp. Usually we can reply in 24 hours on workingg days.
2.Yanwen express: 7-10 working days.We usually ship orders by Yanwen to European countries like German,Greece,Romania,Sweden,France,etc.By yanwen express, customer dont need to pay for tax. Tax is pre-paid. If customer needs faster shipping, please contact salesman.
3.US, UK, EU shipping directly fast and no tax : 3-5 working days.We have stocked up hot sale items in US, UK, EU Warehouse ,which is more convenient for you. Free TAX, faster shipping with cheaper price.
Click and check items in US Warehosue UK Warehouse
About Cancellation Policy
1.You can get a full refund if you make cancellation within 24hours. Because usually we will ship out package within 24 hours, for get full refund, please send us a cancellation note via order center or email.
2.If your cancellation made after 24 hours, please contact our customer service first, you can easily get touch with our customer service via email or any online contact method like skype, whatsapp or online chat. If customer service confirm your order have not been ship out, you can get a full refund
3. If your order has been proceed but have not get out of China(including Hongkong area), you can still cancel our order but you have to pay for the cancellation fee.(Detail fee please consult customer service for your order)
4. If the order already out of China, the order can not be canceled. If you want cancel it, you need send it back after you receive the package and you will need to undertaken the return fee.